How To Improve Wood Fuel Pellet Production Quality ?
As a clean, renewable and economical energy, the global production and use of wood fuel pellets has increased significantly in recent years. The development and utilization of wood waste and biomass can not only address the demand for low-carbon energy and reduce environmental pollution, but can also facilitate the achievement of carbon neutrality. However, there are many factors justifying the case for low utilization of agricultural residues. These factors could be well controlled by producing top-quality pellets. Production of pellets is generally accompanied by the problems of high energy consumption and serious mold wearing. Therefore, how to produce high quality wood pellets becomes an important issue.
In the market of biomass, high quality wood pellets refers to those with rather low ash content. Usually, there are 2 indicators that determines the quality of wood pellets: mechanical durability and water content.

What Effect Wood Fuel Pellet Quality ?
1.Raw Materials Composition
Naturally, the composition of the biomass material directly influence the wood pellet production quality. High lignin content biomass can be easily molded into pellets because of lignin are the natural binders. Low lignin content wood waste should have binders added to achieve a better bonding effect.Hardwood and softwood pellets have different burning characteristics, with hardwood providing a longer burn time and higher heat output than softwood. However, softwood pellets are known for their fast ignition, producing more energy in a shorter period. Your choice of the material source should be based on cost, local availability, and targeted market preferences in terms of pellet performance.

2.Raw Materials Moisture Content
Raw material moisture content has clear impact on the wood pellet production density and molding rate. Proper moisture may help to increase the bond within the pellets by spreading the natural lignin, the inborn binder, evenly within the pellets and increase the compression in the die holes of pellet die. However, too much moisture may lower the bonding strength and even block the pellet die holes.This impact have certain regularities.
When the moisture content is 12%, the molding rate and the pellet density is the lowest.
When the water content is 14~18%, the molding rate and the pellet density reach the top. After that, with the increase of water content, the molding rate and pellet density drop down.
When the water content reach 22%, the molding rate is lower than 50% and the density is low.
3. Raw Materials Particle Size
The particle size of your raw material directly affects the pelletizing process and end product quality. Smaller particles tend to bind together more easily during compression, resulting in higher-density pellets with a consistent shape and size. On the other hand, larger particles lead to an uneven pellet structure and can cause breakdowns during conveyance, handling, and storage.
Raw materials like wood chips and sawdust need to be processed by crushing and grinding equipment to achieve the desired particle size. Implementing proper sieving and grading mechanisms can help remove oversized particles, ensuring a smooth and efficient production process.

4. Ash Content and Additives
The ash content of your raw materials plays a pivotal role in determining the combustion efficiency and clean-burning aspects of your wood pellets. Materials with high ash content produce more residue when burned, leading to increased maintenance and cleaning requirements for end-users. Additionally, the higher ash content in the starting material can cause slogging and clinker formation, negatively impacting the pellet combustion process.
It’s essential to select raw materials with low ash content and to carefully monitor the addition of additives during the pellet production process. Usually, the moisture together with the water soluble compounds such as starch and lignin functions as a binding agent as well as a lubricant to increase the pellet durability by increasing the contact area between the particles. However, the durability value will be decreased when the lignin and other extractives is more than 35%.
How To Make Better Wood Fuel Pellet Production?
To make good wood pellets production, the raw materials must be crushed and its moisture content must be regulated. The most crucial phase in the manufacturing process is biomass pelletizing, which necessitates the presence of a wood pellet plant.
1.The Wood Material Needs To Be Crushed To Small Size.
Collect the wood material to be used and reduce it to smaller sizes as possible. Raw materials are various such as raw tree,wood waste (sawdust, wood shaving etc.), farm waste (straw from plants, corn stalks and corn cobs etc.), yard debris (grass, leaves, tree sticks etc.) and other biomass materials.For bigger wood pieces, such as logs or round wood, a wood crusher is used to crush the material into smaller wood blocks, which are then fed into a wood chipper to make chips for further usage. A hammer mill machine is used to turn farm waste into powder, which is required if pellets with a diameter of 6mm or less are wanted.

2.Control The Moisture Content Of Raw Materials
The recommended content moisture is 10-20%. Excess water must be removed from the raw material in order to generate quality wood pellets. A wood pellet dryer machine is used to remove surplus water in commercial pellet manufacturing. Smaller scale manufacturers can dry the material in the sun or using alternative ways.
3.Choice The Right Wood Pellet Machine
The shredded wood chip powder is fed into the wood pellet machine via a feeder into the pelletizing chamber, a rotating arm presses the powdered wood fibre through a grate featuring a number of small holes at high speeds. This produces extrusion force and high temperatures, which modify the intermolecular forces in the wood substance, enhancing its flexibility. The materials are then molded into pellets by the die’s hole and pushed out.

4.Cooling The Produced Fuel Pellets
In order to make the best wood pellets, air cooling is the necessary process to turn hotly extruded pellets into harden and strengthened. Once the pellets leave the press, they are very hot and plastic, easily deformable product at this time. Every effort must be made to handle this product as gently as possible until it is cooled, dried and hardened. After cooling, the final moisture content will be as low as 6% and the pellets will be transported through the conveyor belt to the storage shed. A wood pellet packing machine is subsequently used to pack the pellets into plastic bags for transport or sale. Huge amounts of wood pellets are carried in bulk trucks to bulk storage containers, resulting in a more efficient processing system.

Conclusion
The global wood pellets market size was estimated at USD 8.23 billion in 2021 and is expected to reach USD 8.55 billion in 2022,which is expected to grow at a compound annual growth rate of 5.5% from 2021 to 2030 to reach USD 13.38 billion by 2030. Through the relevant researches in recent years, it is obvious that the wood pellets market has a good future and there is still a big demand of wood pellets over the world. On the other hand, compared with traditional fuel options, wood pellets are more friendly to the environment. It will be an important part of the development of environment protection. Besides, as a new fuel option, wood pellets can turn the raw materials into fully burning. That is to say, a little wood, a lot heating. No matter for home-use or for trade, wood pellets business still has a good future.